/*
* Header File for the Telescope Control protocols for the Meade LX200
* Author:  John Kielkopf (kielkopf@louisville.edu)
*
* This file contains header information used in common with xmtel.
*
* 15 May 2003 -- Version 2.00
*
*/


#ifndef CELESTRON_PROTOCOL_H
#define CELESTRON_PROTOCOL_H

/* These are user defined quantities that set the limits over which it */
/* is safe to operate the telescope.  */


/* LOWER is the number of degrees from the zenith that you will allow. */
/* Use 80, for example, to keep the eyepiece end out of the fork arm space */
/* of an LX200 telescope. */

#define LOWER         90.

/* HIGHER is the horizon.  0 is an unobstructed horizon in every direction. */
/* Use 10, for example, to limit sighting below 10 degrees above the horizon. */

#define HIGHER         0.


/* Set this if a slew to the north sends the telescope south. */

#define REVERSE_NS	0 	/* 1 for reverse; 0 for normal. */


/* Set this for maximum slew rate allowed in degree/sec. */

#define MAXSLEWRATE	4 	/* 2 for safety; 4 for 16-inch; 8 otherwise. */




/* The following parameters are used internally to set speed and direction. */
/* Do not change these values. */


#define	SLEW		0
#define	FIND		1
#define	CENTER		2
#define	GUIDE		3

#if REVERSE_NS > 0
#define	NORTH		3
#define	SOUTH		0
#else
#define	NORTH		0
#define	SOUTH		3
#endif

#define	EAST		2
#define	WEST		1

/* Slew speed defines */

# define SLEWRATE8     8    /* should be 8 degrees per second (not 16-inch) */
# define SLEWRATE4     4    /* should be 4 degrees per second */
# define SLEWRATE3     3    /* should be 3 degrees per second */
# define SLEWRATE2     2    /* should be 2 degrees per second */

/* Reticle defines */

#define BRIGHTER        16  /* increase */
#define DIMMER          8   /* decrease */
#define BLINK0          0   /* no blinking */ 
#define BLINK1          1   /* blink rate 1 */
#define BLINK2          2   /* blink rate 2 */
#define BLINK3          4   /* blink rate 3 */
 

/* Focus defines */

#define FOCUSOUT        8   /* positive voltage output */
#define FOCUSIN         4   /* negative voltage output */
#define FOCUSSTOP       0   /* no output */ 
#define FOCUSSLOW       1   /* half voltage */
#define FOCUSFAST       2   /* full voltage */


/* Rotator defines */

#define ROTATORON        1   /* image rotator on */
#define ROTATOROFF       0   /* image rotator off */


/* Fan defines */

#define FANON        1   /* cooling fan on */
#define FANOFF       0   /* cooling fan off */

#ifdef __cplusplus
extern "C" {
#endif

int ConnectTel(char *port);
void DisconnectTel(void);
int  CheckConnectTel(void);

void SetRate(int newRate);
void SetLimits(double limitLower, double limitHigher);
void StartSlew(int direction);
void StopSlew(int direction);
double GetRA(void);
double GetDec(void);
int  SlewToCoords(double newRA, double newDec);
int  SyncToCoords(double newRA, double newDec);
int  CheckCoords(double desRA, double desDec);

void StopNSEW(void);
int  SetSlewRate(void);

int  SyncLST(double newTime);
int  SyncLocalTime();

void Reticle(int reticle);
void Focus(int focus);
void Derotator(int rotate);
void Fan(int fan);

#ifdef __cplusplus
}
#endif

#endif